The Store

The Repair 24 Auto/Boat/Plane Section

2 Ton 10'' Lift Hand Chain Hoist

(JET101712) 2 Ton 10'' Lift Hand Chain HoistFeatures: All purpose hand chain hoist features impact resistant, lightweight steel construction with durable powder coat finish. Needle bearing supported load sheave for long life and low wear. Triple spur gears provide high efficiency ratio. Low headroom for easy installation even in confined areas. Compact and portable with excellent load spotting capabilities. Induction hardened, corrosion resistant grade 80 load chain. Hand chain cover designed for smooth operation and prevents side pull jamming. Completely enclosed Weston type automatic brake system with two ratchet pawls for positive load control. Drop forged safety hooks with durable latches swivel 360�?? for easy rigging. Proof tested and certified. Complies with OSHA, ANSI/ASME B30.16 and HST-2M standards.

$325.16
Click To Buy

Diaphragm Hand Pump

(JET140031) Diaphragm Hand PumpFeatures: Fits 15 to 55 gallon drum with 2"" bung openings. Hardened steel lockable handle. Self-lubricating seal. Two-piece inlet pipe with joint adapter. 8�? gasoline resistant discharge hose with straight type nozzle. For use in dispensing gasoline, diesel fuel, oil, alcohol and lubricants. Piston can be reversed to change flow direction of pump. Not to be used with solvents, acids, alkalis, water or other corrosive liquids.

$170.03
Click To Buy

Steel Drum Dollies

(JET140121) Steel Drum DolliesFeatures: Smooth rolling, strong and durable dollies easily transport 30 or 55 gallon drums. All welded 1/8"" x 2 1/8"" steel frame and 3-1/8.

$40.97
Click To Buy

14 Gallon Oily Waste Can

(JUS09500) 14 Gallon Oily Waste CanFeatures: Wherever essential solvent soaked rags and wipes are used, durable galvanized steel cans minimize the risk of spontaneous combustion. Raised, flow-through base encourages circulation of air around can to disperse heat. Self-closing cover reduces oxygen source and snaps shut automatically when easy-to-use foot pedal is released. Smaller countertop model is ideal where work space is at a premium or when floor model is not practical. Factory Mutual (FM) tested and approved. Underwriters Laboratories (UL) listed Foot operated cover. Dimensions: 16.063"" outer diameter x 20.25"" height. Factory Mutual (FM) tested and approved. Underwriters Laboratories (UL) listed

$70.07
Click To Buy

1 Gallon Steel Plunger Can

(JUS10308) 1 Gallon Steel Plunger CanFeatures: 1 gallon Perforated pan screen serves as a flame arrester. Top rim has molded edge protectors for smooth, trouble-free moistening. 24-gauge steel constuction. Finished in a tough, chemical resistant powder paint. Steel dasher assembly, brass plunger assembly. 7.25"" outer diameter x 11"" height, 5"" dasher diameter. Factory Manual (FM) tested and approved. Backed by industry exclusive Ten-Year Limited Warranty

$51.15
Click To Buy

Smokers Cease-Fire Cigarette Butt Recepticle - Pewter Grey

(JUS26800) Smokers Cease-Fire Cigarette Butt Recepticle - Pewter GreyFeatures: The safe and attractive answer to cigarette butt disposal to keep your property clean. Self-extinguish design safely collects unsightly cigarette butts and reduces the risk of fire. Made of sturdy polyethylene: low maintenance, won''t rust, dent, or crack. Unique rain bonnet opening keeps rain out and discourages other trash. Simply lift off lid to empty big galvanized steel pail inside. Tie-down notches offer security and greater stability under severe weather conditions. In high humidity environments, unique ""drip-lip"" internal construction prevents tar condensation from escaping. Factory Mutual (FM) tested and approved. Specifications: Polyethylene butt receptacle with liner pail Dimensions: 16.5"" Outer Diameter x 38.5 Height Color: Pewter Grey

$54.83
Click To Buy

Smokers Cease-Fire Cigarette Butt Recepticle - Adobe Beige

(JUS26800B) Smokers Cease-Fire Cigarette Butt Recepticle - Adobe BeigeFeatures: The safe and attractive answer to cigarette butt disposal to keep your property clean. Self-extinguish design safely collects unsightly cigarette butts and reduces the risk of fire. Made of sturdy polyethylene: low maintenance, won''t rust, dent, or crack. Unique rain bonnet opening keeps rain out and discourages other trash. Simply lift off lid to empty big galvanized steel pail inside. Tie-down notches offer security and greater stability under severe weather conditions. In high humidity environments, unique ""drip-lip"" internal construction prevents tar condensation from escaping. Factory Mutual (FM) tested and approved. Specifications: Polyethylene butt receptacle with liner pail Dimensions: 16.5"" Outer Diameter x 38.5 Height Color: Adobe Beige

$54.83
Click To Buy

5 Gallon Steel Dip Tank

(JUS27605) 5 Gallon Steel Dip TankFeatures: Portable, safe solution to parts cleaning. Useful for cleaning parts and subassemblies where the volume of work does not warrant use of a larger rinse tank. Easily moved to accommodate changing production requirements. Manually operated cover stays open for convenient access. Cover is equipped with a self-closing mechanism and fusible link which melts at 165�?? F to snap the cover shut in case of fire. Constructed of 24-gauge coated steel. Finished in a durable powder coat paint for long use. Dimensions: 13.75"" Outer Diameter x 13"" Height. Factory Mutual (FM) tested and approved, Underwriters Laboratories (UL) listed.

$84.34
Click To Buy

Master Spindle Rethreader Die Set

(KAS2599) Master Spindle Rethreader Die SetFeatures: This 20 piece set will repair or renew damaged threads on stub axles/spindles on most vehicles. Dies are made from high tempered steel for strength and durability. Sizes include: 11/16""-24, 3/4""-16, 3/4""-20, 13/16""-20, 27/32""-20, 7/8""-14, 1""-14, M16X1, M16X1.5, M18X1.5, M19X1.5, M20X1, M20X1.25, M20X1.5, M22X1, M22X1.5, M24X1.5, M24X2, M25X1.5 and M27X2 in a Blow Molded Case.

$69.65
Click To Buy

Master Power Steering Pump and Alternator Remover/Installer Kit

(KAS5238) Master Power Steering Pump and Alternator Remover/Installer KitFeatures: Removes and installs press-on-type belt drive accessory pulleys. Interchangeable components to work on GM Quad 4, GM 3.1L, and Ford 4.6L Works with hand tools or an impact gun. Kit includes a special holding bar to stop housing from spinning during use with impact gun.

$69.65
Click To Buy

3-Pc. Universal Ratcheting Serpentine Belt Wrench Set

(KAS5344) 3-Pc. Universal Ratcheting Serpentine Belt Wrench SetFeatures: The Serpentine Belt Wrenches are designed to release the tension on spring-loaded idler pulleys. This wrench allows direct access to the tensioner without having to remove engine accessories or frame components. Ratcheting wheels allow quick and easy positioning of the wrench driving end to allow the user to access the tensioner from any angle. Heat treated and nickel chrome plated for durability, appearance and long tool life. Slim head design allows access to tight areas found in the tensioner area on some front wheel drive vehicles. Sizes: 13mm or 1/2"" Hex, 14mm Hex, 15mm Hex, 16mm or 5/8"" Hex, 17mm Hex, 18mm Hex, 19mm or 3/4"" Hex, 3/8"" Square, 1/2"" Square, 3/4"" Square

$77.00
Click To Buy

Ratcheting Bolt Wrench for Harley-Davidson Rocker Box Covers

(KAS6529) Ratcheting Bolt Wrench for Harley-Davidson Rocker Box CoversFeatures: For installation and removal of all Harley-Davidson Evolution motor rocker box covers. Reversible ratcheting action - If using a conventional wrench, installers may unscrew the bolt up to the frame. Without the ability to reverse with a ratcheting wrench, the bolt will be lodged in that position Low profile design gets into the tight spaces between engine and frame 9-3/4"" long handle for increased reach Comfortable rubber grip will not scratch chrome 3/16"" Allen bit is replaceable Made in the U.S.A.

$36.18
Click To Buy

6 Pc. Wheel Stud Installer Kit for Automobiles

(KAS938) 6 Pc. Wheel Stud Installer Kit for AutomobilesFeatures: This kit assures correct installation of wheel studs the first time, every time. No more ruined studs or lug nuts, and no more wasted time. Easy instruction / diagram sheet included. Automotive kit includes installer sizes: 7/16""-20, 1/2""-20, 12mm-1.25 and 12mm-1.50, as well as a spacer and washer.

$62.13
Click To Buy

11 Pc. Gasket Hole Punch Set

(KAS950) 11 Pc. Gasket Hole Punch SetFeatures: Designed to cut holes and internal radii in gaskets and other soft material such as rubber, lead foil, linoleum, felt fiber and other similar materials. Contains long driving mandrel. Ten punch sizes: 1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 3/4, 7/8, 1.

$32.35
Click To Buy

Automatic Transmission Clutch Spring Compressor

(KD2398) Automatic Transmission Clutch Spring CompressorFeatures: Tool compresses automatic-transmission clutch springs on some GM, Ford, Toyota and other transmissions. It permits easy removal and installation of snap rings. Job can be completed without removing center shaft and clutch assembly from transmission housing. To use, force legs in and catch jaws inside transmission drum groove. Loosen wing nuts and adjust pushers. Tighten screw until lock ring is free to be removed.

$99.01
Click To Buy

Pulley Puller and Installer Set

(KD2897) Pulley Puller and Installer SetFeatures: Remove pressed-on alternator and power steering pulleys on late-model GM, Ford and Chrysler engines. The threaded end installs late-model GM alternator and power steering pulleys, including Quad 4. Reverse the jaws to pull the alternator internal bearing. The puller fits some AMC''s. Will not work on 3.3L and 3.5L Chrysler engines. Includes: Puller Body, Jaw and Sleeve Assembly, Jackscrew, Button, Bearing and Washer, Puller Pin for Quad 4, Screw Installer for Quad 4, Puller Pin for GM 3.1, Screw Installer for Ford 4.6 and Screw Installer for All Others.

$44.83
Click To Buy

3/4" Dr. Micrometer Torque Wrench - 100 to 600 Ft.-Lbs.

(KD2953) 3/4" Dr. Micrometer Torque Wrench - 100 to 600 Ft.-Lbs.Features: Torque range: 100 to 600 ft.-lbs in 2.5lb increments; (153 to 830 Nm in 3.4 Nm increments) Reversible for torquing left or right threaded fasteners Accurate in clockwise direction to +/- 4% in upper 80% of range Micrometer lock-ring maintains setting during operation Rubber dust seal keeps dirt out of inner mechanism 45 tooth ratchet design yeilds 8 degree arc for work in tight spaces Chrome finish for long lasting corrosion resistance Length: 41.25"" Includes storage box

$452.80
Click To Buy

Deluxe Universal Overhead Valve Spring Compressor

(KD3271) Deluxe Universal Overhead Valve Spring CompressorFeatures: Compressor easily removes valve springs on most cars and light trucks. Tool can be used with the cylinder head on or off the engine. Features a removable handle allowing use with 5/8"" socket or wrench in confined areas and an extra-long leg for more applications. For best results, use with 901 or 2992 Air Hold Fittings to pressurize the cylinder and keep the valves in place during removal of the spring and keepers. Includes: Long Leg, length 3 15/32"", Short Leg, length 3 5/32""

$33.28
Click To Buy

Drum Brake Resetting Tool

(KD3377) Drum Brake Resetting ToolFeatures: This quality tool is used to set the proper clearance between brake lining and drum prior to assembly. Inside calipers measure drum diameters and outside calipers transfer measurement to brake shoes. Knurled know locks tool at measurement. Working drum diameter range: 6-1/2"" to 14-1/4"". Calibrated in 1/32"" (1mm) increments

$35.26
Click To Buy

3/8" Drive Micrometer Torque Wrench

(KD3459) 3/8" Drive Micrometer Torque WrenchFeatures: Fast, accurate and easy to use torque wrenches have accuracy +/-4% right hand (clockwise) and +/-6% left hand (counter clockwise). Reversible ratchet head features a 45-tooth ratchet design requiring only 8 degrees of hand travel for indexing. English and metric markings are color coded for easy reading. Ball bearing-mounted internal torque control mechanism provides proper lubrication, high accuracy, prolonged calibration life and consistent results. Positive, spring-loaded locking mechanism automatically locks in the selected reading to prevent accidental change. English Range: 25 to 250 in.-lb. (1 in.-lb. grad.) Metric Range: 3.61 to 29.03 Nm (.11 Nm grad.) Length: 13.1""

$90.24
Click To Buy

3/8" Drive Micrometer Torque Wrench

(KD3460) 3/8" Drive Micrometer Torque WrenchFeatures: Fast, accurate and easy to use torque wrenches have accuracy +/-4% right hand (clockwise) and +/-6% left hand (counter clockwise). Reversible ratchet head features a 45-tooth ratchet design requiring only 8 degrees of hand travel for indexing. English and metric markings are color coded for easy reading. Ball bearing-mounted internal torque control mechanism provides proper lubrication, high accuracy, prolonged calibration life and consistent results. Positive, spring-loaded locking mechanism automatically locks in the selected reading to prevent accidental change. English Range: 10 to 100ft.-lb. (.5ft.-lb. grad.) Metric Range: 16.9 to 138.9 Nm (.7 Nm grad.) Length: 17.4""

$94.11
Click To Buy

1/2" Drive Micrometer Torque Wrench

(KD3461) 1/2" Drive Micrometer Torque WrenchFeatures: Fast, accurate and easy to use torque wrenches have accuracy +/-4% right hand (clockwise) and +/-6% left hand (counter clockwise). Reversible ratchet head features a 45-tooth ratchet design requiring only 8 degrees of hand travel for indexing. English and metric markings are color coded for easy reading. Ball bearing-mounted internal torque control mechanism provides proper lubrication, high accuracy, prolonged calibration life and consistent results. Positive, spring-loaded locking mechanism automatically locks in the selected reading to prevent accidental change. English Range: 25 to 250 ft.-lb. (1 ft.-lb. grad.) Metric Range: 43.4 to 348.4 Nm (1.4 Nm grad.) Length: 20.5""

$111.98
Click To Buy

Fan Clutch Wrench Set

(KD3472) Fan Clutch Wrench SetFeatures: Includes the Universal Pulley Holder part #3471 plus fan clutch wrenches #3422 and 3136-76. Used to remove and replace thermostatic fan assemblies while eliminating the need for various size holding wrenches. Applications include: Ford trucks w/2.8L, 2.9L, 3.0L, 4.0L, 4.9L and 5.0L engines. Dodge trucks w/3.9L, 5.2L, 5.9L, 8.0L V10 engines. GM trucks w/4.3L, 5.0L and 5.7L engines. Jeeps w/5.2L engines. Includes: Universal Pulley Holder; Wrench (40mm); Wrench (36mm)

$47.25
Click To Buy

GearWrench Serpentine Belt Tool

(KD3680) GearWrench Serpentine Belt ToolFeatures: 100% coverage of all vehicles including the 3/4 Volvo Ratcheting GearForce technology provides exceptional access and ease of use Both crow foot and socket size included for increased versatility Comes with blow molded storage case.

$54.81
Click To Buy

Cooling System and Radiator Cap Tester Combo Kit

(KD3700) Cooling System and Radiator Cap Tester Combo KitFeatures: Pressure test both Cooling Systems and Radiator Caps with One Kit! Features: Universal Cooling System Adapter - Patented ""Bladder System"" allows for virtually 100% coverage for domestic and foreign cars. Radiator Cap Adapter Kit - 8 sizes for virtually complete coverage. Allows both cap relief pressure and seal condition to be tested. Includes: Hand pump with gauge, universal cooling system adapter, 4 radiator cap adapters (8 sizes), molded case, and instructions.

$120.86
Click To Buy

2 Pc Brake Bleeding Master Set

(KD3712) 2 Pc Brake Bleeding Master SetFeatures: 2 Pc Brake Bleeding Master Set The NEW 3712 combines the new high capacity Quick Draw (3710) and the new automatic reservoir refill bottle (3711) to form the ultimate one-person brake bleeding kit.

$99.27
Click To Buy