The Store

The Repair 45 Auto/Boat/Plane Section

Chrysler LH Toe Adjusting Tool Set

(OTC6272) Chrysler LH Toe Adjusting Tool SetFeatures: Enables technician to adjust toe, obtain a straight steering wheel, and correctly center the tie rod end. Permits easily reaching and breaking loose the tire rod jam nuts while the entire assemble is held stable. Services 1998-newer Chrysler Concorde, 300M, New Yorker LHS, Dodge Intrepid, Dodge R/T, and Eagle Vision

$103.20
Click To Buy

Tie Rod/Pitman Arm Adjusting Set - 5 Pc.

(OTC6275) Tie Rod/Pitman Arm Adjusting Set - 5 Pc.Features: Consists of one Pitman arm and four tie rod tools in a blow-molded storage case.

$85.46
Click To Buy

Front Hub Puller for 4WD Vehicles

(OTC6290) Front Hub Puller for 4WD VehiclesFeatures: For removal of the front hub assembly, necessary for wheel bearing or brake rotor service. Provides the mechanical advantage and straight pull not possible with a slide hammer. Services: 1988-2000 GM 1/2-ton, 3/4-ton, and 1-ton trucks, Tahoe, Suburban, and Yukon 1994-2000 Dodge 1/2-ton, 3/4-ton, and 1-tonRam trucks 1997-2000 Ford 1/2-ton trucks, and Expeditions; 1998-2000, Ford 3/4-ton and 1-ton trucks, and Excursions 1985-2001 Jeep Cherokee.

$89.37
Click To Buy

Front End Service Tool Set - 5 Pc.

(OTC6295) Front End Service Tool Set - 5 Pc.Features: This kit includes five popular tools used for servicing Pitman arms, ball joints, and tie rods on most vehicles. Two Pitman Arm Pullers for large or small ball joint applications. Two Ball Joint Separators. Three different Tie Rod Pullers. All tools can be purchased individually.

$132.61
Click To Buy

Ford Cam Positioning Master Tool Set

(OTC6489) Ford Cam Positioning Master Tool SetFeatures: The OTC Ford Cam Tools ensure correct cam timing when servicing timing belts, chains, head gaskets or other valve train repairs. OTC Ford Cam Tools avoid improperly timed cams that can cause poor performance, poor mileage, and possible vehicle ""check engine"" light engagement. The 22 tools in the 6489 Master Kit cover 1989 thru 2002 applications and comes in a molded storage case. All individual tools are available separately.

$385.71
Click To Buy

Clamshell Strut Spring Compressor

(OTC6494) Clamshell Strut Spring CompressorFeatures: Servicing MacPherson struts is convenient and affordable with this compressor. It fits a wide range of struts and requires no special adapter shoe. Safety locking pins hold the compressor jaws in place. Tool compresses springs of 4"" to 9"" O.D., with wire diameters of 7/16"" to 11/16"". Built to use with an impact wrench.

$245.09
Click To Buy

Pitman Arm Puller - Compact Design for SUV

(OTC6496) Pitman Arm Puller - Compact Design for SUVFeatures: New patented design saves time, increases productivity. Labor intensive removal of steering sector is now unnecessary. Compact design of puller allows easy access to the Pitman arm. Live center on forcing screw and easy use of a standard wrench results in less effort required. Works on most domestic SUVs and pickups. Tool is forged steel for durability and long life. Pays for itself on its first job. Works on the following four-wheel-drive vehicles: 1998 - 2002 Lincoln Navigator 1997 - 2002 Ford F-150 and Expedition 1991 - 2001 Oldsmobile Bravada 1991 - 2001 S10/S15 GM Trucks and Blazers 1992 - 2002 Suburban 1988 - 2002 GM and Chevy 1/2-, 3/4- and 1-ton pickups 1992 - 2002 Chevy Tahoe and GMC Yukon

$61.28
Click To Buy

Ford 4.6L 4-Valve Cam Timing Kit

(OTC6498) Ford 4.6L 4-Valve Cam Timing KitFeatures: Works on: - 1993-04 Ford, Lincoln, and Mercury - 1993-98 Lincoln Mark Series - 1995-02 Lincoln Continental - 1996-04 Ford Mustang - 2003-04 Mercury Marauder - 2003-04 Lincoln Aviator vehicles with 4.6L 4-valve V-8 engine. Kit includes: Camshaft positioning tool, camshaft holding tool, crankshaft positioning tool, secondary chain tensioner tool. Saves time; all tools required for camshaft timing are in one kit.

$116.09
Click To Buy

4 Pc. Fuel/Oil Line Disconnect Tool Set

(OTC6507) 4 Pc. Fuel/Oil Line Disconnect Tool SetFeatures: Four of the most popular size fuel and oil line disconnect tools used on GM, Ford and Chrysler vehicles. Tools are color coded to work on the following lines: Black - 1/4"" fuel line Red - 5/16"" fuel line Gold - 3/8"" fuel line Blue - transmission oil line

$34.06
Click To Buy

Master Disconnect Tool Set

(OTC6508) Master Disconnect Tool SetFeatures: 3/8"", 1/2"", 5/8"", and 3/4"" disconnect tools for Ford and Chrysler A/C line service. 3/8"" and 1/2"" disconnect tools for Ford fuel lines. 5/8"" disconnect tool for Ford heater hoses. 5/16"" and 3/8"" fuel line disconnect tools for GM and Chrysler. Transmission oil cooler line disconnect for Ford and GM vehicles. Fuel line disconnect tool for 1990-1994 Ford Ranger, Explorer, Bronco II. Heater hose disconnect tool for Ford Aerostar vans and Econoline vans and Chrysler vehicles. Oil cooler disconnect tool for Ford vehicles. Clutch coupling release tool for Ford trucks and Cougar/Thunderbird. Fuel line disconnect tool for Chrysler vehicles. Heater hose disconnect tool for GM vehicles. Long-handle disconnect tools for Ford and GM fuel lines. Scissors-style fuel line disconnect tools 5/16"", 3/8"", and 1/2"" for Ford and GM vehicles. Toyota A/C line disconnect tool. GM hydraulic clutch line disonnect tool. GM oil cooler disconnect tool. 1/4"", 5/16"", and 3/8"" universal disconnect tools. Universal transmission line disconnect tool. Comes in blow-molded plastic case.

$140.38
Click To Buy

Leak Tamer Plus EVAP

(OTC6521) Leak Tamer Plus EVAPFeatures: Easy, effective, versatile tool to help technicians diagnose EVAP trouble codes on domestic and import cars and light trucks. Uses patented UltraTraceUV technology - the only OEM-approved dye available. Works with nitrogen or shop air to meet all OEM test requirements. Uses existing OTC LeakTamer accessories. Uses OEM-Approved Technology This technology was developed in collaboration with Ford Motor Company, GM, and Daimler Chrysler to specifically test a vehicle�?s EVAP system and to meet major automakers�? EVAP testing specifications and needs. The LeakTamer Plus EVAP Model 6521 is EVAP-approved. Replacement UltraTraceUV smoke compound available - order# OTC P-0716-UV. Accessories Included with No. 6521 No. CEA-01 - 3 1/2"" Diameter Exhaust Cone No. CEA-02 - Assorted Cap Plug Kit No. CEA-04 - Standard Service Port Adapter No. CEA-049 - Dual Size Schrader Removal Tool No. HS-400AC - 400,000 CP Spotlight with 20 foot Cord and Battery Clips No. 6525-4 Water Filter

$999.75
Click To Buy

LeakMaster Evaporative Emissions System Tester

(OTC6525) LeakMaster Evaporative Emissions System TesterFeatures: Developed specifically to diagnose vehicle EVAP system for leaks. Can also be used to diagnose and locate vacuum leaks, exhaust leaks, under dash vacuum leaks, crankcase oil leaks, and wind and water leaks. Shipped with full charge of smoke producing UV solution that can be refilled by the customer. Accessories to test EVAP systems on many import & domestic vehicles included.

$1675.71
Click To Buy

Ball Joint Remover/Installer Super Set

(OTC6530) Ball Joint Remover/Installer Super SetFeatures: This set allows for the removal and installation of press-fit ball joints on many GM and Ford light-duty trucks, vans and SUVs through 2003; Dodge light trucks through 1998; Dodge vans, Durango and Dakota through 2003; and Honda Accord, Civic, del Sol, and Prelude through 2001. Combines the popular OTC 7249, 7918 and 7996 ball joint sets into one SUPER set, competitively priced. The OTC designed and produced C-frame tool can be used alone to remove and replace universal joints. Comes complete with an application cross reference and instructions in a blow-molded case.

$270.91
Click To Buy

HubTamer Elite Front Wheel Drive Service Tool Set

(OTC6537) HubTamer Elite Front Wheel Drive Service Tool SetFeatures: Taking a Winner and making it Better! Works on virtually all floating and trapped rotors found on domestic and import vehicles. Fits behind the rotor. Pushes on the steering knuckle, not the rotor. Eliminates the need to remove the knuckle assembly. No need for a shop press or unnecessary front end alignments. New Ford adapter included for use on Taurus/Sable 1986-1995 and Contour/Mystique 1995-newer vehicles! Puller and adapter improved with addition of a beveled edge for easier use in tight fit applications. Impact wrench compatible. Updated molded case and application information.

$337.92
Click To Buy

Master Fuel Injection Tester Kit - Import and Domestic

(OTC6550) Master Fuel Injection Tester Kit - Import and DomesticFeatures: Test fuel injection systems on most GMs, including GM TBI, Ford, Chrysler, and Jeep vehicles. Also works on imports, including CIS and CISE fuel systems. With this new kit you can diagnose fuel-related problems, such as a weak fuel pump or restricted fuel filter, and perform leak-down tests. Kit includes 0-100 PSI fuel pressure gauge and 35 of the popular OTC fuel injection adapters, each equipped with a quick-connect Schrader valve for safety. Replacement seal kit also included

$257.99
Click To Buy

Domestic Fuel Injection Tester Kit

(OTC6551) Domestic Fuel Injection Tester KitFeatures: Test fuel injection systems on most GMs, including GM TBI, Ford, Chrysler, and Jeep vehicles. With this new kit you can diagnose fuel-related problems, such as a weak fuel pump or restricted fuel filter, and perform leak-down tests. Kit includes 0-100 PSI fuel pressure gauge and 17 of the popular OTC fuel injection adapters, each equipped with a quick-connect Schrader valve for safety. Replacement seal kit also included.

$240.46
Click To Buy

Import Fuel Injection Tester Kit

(OTC6552) Import Fuel Injection Tester KitFeatures: Test fuel injection systems on imports, including CIS and CISE fuel systems. With this new kit you can diagnose fuel-related problems such as a weak fuel pump or restricted fuel filter, and perform leak-down tests. Kit includes 0-100 PSI fuel pressure gauge and 23 of the popular OTC fuel injection adapters, each equipped with a quick-connect Schrader valve for safety. Replacement seal kit also included.

$190.28
Click To Buy

StrutTamer Elite Stand

(OTC6582) StrutTamer Elite StandFeatures: The OTC StrutTamer Elite stand features steel frame construction with two wheels that allow you to easily tilt the stand back and move the entire unit to the work area. To keep it firmly in place during compression, the wheels lift off the floor, and four no-slip rubber pads keep the stand firmly in place during operation. The stand is narrower for easier mobility between vehicles in the shop. Height 44"" (1118 mm) Width 22-1/2"" (572 mm) Depth 32"" (813 mm)

$196.65
Click To Buy

EVAP Cart for OTC Leakmaster 6525

(OTC6625) EVAP Cart for OTC Leakmaster 6525Features: Recessed area on top of the cart allows smoke machine to fit tightly and ensures its safety from tipping. Holding well for a standard sized SAE nitrogen tank of 60 or 75 cubic foot. Large shelf area for the adapter and other accessories that come with the smoke machine. Raised handle, large recessed rollers, and a minimum floor footprint for ease in moving the unit around the shop floor.

$322.44
Click To Buy

Stinger Fractional Stud Remover Set - 4 Pc.

(OTC6986) Stinger Fractional Stud Remover Set - 4 Pc.Features: Designed to be the best professional extractors available and tested to reach studs in difficult work areas. Housed in a blow-molded storage case. Includes: 3/8"" drive for 1/4"" & 5/16"" stud sizes, and 1/2"" drive for 3/8"" and 7/16"" stud sizes.

$50.45
Click To Buy

Stinger Metric Stud Remover Set - 4 Pc.

(OTC6987) Stinger Metric Stud Remover Set - 4 Pc.Features: includes: 3/8"" drive for 6mm and 8mm stud sizes, and 1/2"" drive for 10mm & 12mm stud sizes

$41.85
Click To Buy

Power Steering Pump Pulley Replacer

(OTC7005) Power Steering Pump Pulley ReplacerFeatures: An ideal companion to the 7185 the 7005 is a real timesaver when it comes to installing power steering pump pulleys and GM press-on water pump pulleys. Wont damage internal components by exerting force through the pump shaft. A roller bearing in the tool allows for easy turning and the tool shape prevents damage to the pump. Threads are 3/8in - 16 to fit the pulley shaft threads. Same as Ford No. T65P-3A733-C.

$41.99
Click To Buy

Upper Control Arm Bushing Service Set

(OTC7068) Upper Control Arm Bushing Service SetFeatures: Includes all adapters needed for quick bushing removal/installation without removing control arm from vehicle. Now you can easily replace press-in type upper control arm bushings on most rear wheel drive Ford GM and Chrysler vehicles. Mechanical screw power quickly removes the worn bushing and installs the new one without damaging the control arm. Includes C-frame screw assembly and all adapters and inserts necessary to do the job correctly.

$296.64
Click To Buy

Yoke Remover

(OTC7075) Yoke RemoverFeatures: Transmission output shaft end yoke remover.

$107.72
Click To Buy

Axle Stud Cone Plier

(OTC7077) Axle Stud Cone PlierFeatures: Now you can easily remove the tapered cone from the studs used on medium- and heavy-duty truck rear axles. This specially designed plier gives you the leverage needed to expand the cone and remove it from the stud for axle removal.

$32.68
Click To Buy

Propane Enrichment Kit

(OTC7148) Propane Enrichment KitFeatures: The No. 7148 ensures proper idle mixture and compliance with emission standards. For use on domesic or import vehicles with carburetors. Uses standard 14 oz. propane cartridge.

$87.71
Click To Buy